GE Stove Repair in Toronto — Electric element not heating

• Oven bake element open-circuit (no/low bake heat): the GE bottom bake element WB44K10005 (2,585W / 240V, replaces WB44K10001) burns out like a light bulb. We confirm with a continuity test across the terminals before condemning it -- if it reads open, it is replaced; a visible blister or arc-spot at the back wall is the giveaway. This is the single most common 'electric element not heating' call on JB/JBS freestanding GE ranges.
• Element tests GOOD but still no bake heat -> oven relay board. On GE Profile/Cafe (PB/PGB, CGS/C2S) the bake relay on the WB27T-prefix oven relay board (e.g. WB27T10821, WB27T11356) opens while the element itself has continuity. We check for 240V across the element terminals with the board calling for heat; broil works but bake is dead points straight at the bake relay, not the element -- swapping the element here is the classic misdiagnosis.
• Glass-top burner dead on a dual-zone element: the WB30T10130 12-inch dual 'haliant' radiant element (replaces AP4344395 / PS2321564) commonly fails so only the outer ring heats, or goes fully cold. We meter continuity at the element pigtail; the 9-inch dual radiant element WB30T10099 fails the same way (often one zone dies first), and the 6-inch single-zone radiant element WB30T10047 simply goes open. The element is not repairable -- it is replaced as a unit.
• Coil-top burner not heating from a burnt receptacle, not the coil: on older GE coil ranges the surface element WB30X0253 (8-inch) draws an arc at the terminal block and chars the WB17X5113 receptacle (AP2021559 / PS232646). We swap the coil into a known-good receptacle to isolate -- if it heats there, the burnt receptacle block gets replaced, and if the prongs are pitted we replace BOTH coil and receptacle so the new contact does not re-burn.
• Burner won't heat (or won't adjust) -> infinite switch, not the element. The WB24T10025 surface burner infinite switch (8-inch, 2,500W, replaces 769692 / PS236750) loses its internal contact and the burner stays cold or stuck on high. We confirm by reading switch output with the knob cycling: no voltage out to a good element means the switch, which is a cheaper fix than the element it is often blamed for.
• RTD oven sensor drift masquerading as 'element not heating': the WB21X5301 oven temperature sensor reads the oven far hotter than it is, so the control cuts element power early and the oven feels like it never heats. F3 / F4 flags the sensor circuit open/short. We meter the RTD (~1080-1100 ohms at room temp, GE spec 1030-1150) -- out of spec and it is replaced; this restores the element's call for heat without touching the element.
• Self-clean aftermath no-heat: GE's high-heat self-clean cycle can pop the oven thermal limit / fuse and leave the bake element cold afterward, sometimes throwing F2 (over-temp runaway) on the way. We check the thermal cutout continuity and the sensor together after any 'it died right after I cleaned it' call -- a weak WB21X5301 sensor or a tripped limit, not the element, is usually the actual no-heat cause.

GE electric element not heating in Toronto — the local specifics

• The recurring Toronto pattern on GE electric-element no-heat splits cleanly by housing age: older coil ranges in established east-end and midtown homes almost always come down to a burnt receptacle block or a tired infinite switch rather than a bad coil, while newer condo and renovated-kitchen glass-top GE/Cafe units are most often an open WB44K10005 bake element or a bake relay on the WB27T board -- so we arrive ready to meter the element AND the receptacle/switch/board path, not just swap parts.
• To these calls we bring the WB44K10005 bake element, WB24T10025 infinite switch, WB21X5301 RTD sensor, and WB30X0253 coil / WB17X5113 receptacle so a typical GE no-heat is fixed on the first visit; WB30T10130 / WB30T10099 glass-top radiant elements and WB27T relay boards are pulled by model number when the on-site meter test points there.

For the full GE stove module — every fault, part number and code — see GE stove repair in Toronto, and for the same fault across all brands the stove electric element not heating guide.