Samsung Stove Repair in Toronto — Gas burner clicks constantly

• Constant clicking that never stops - even with every knob OFF - is moisture in the spark switches on Samsung's NX58/NX60 gas tops before it is ever a failed part. Water from a boil-over or a wet-cloth wipe-down wicks down the knob shaft and bridges the contacts of an igniter switch, which then feeds the shared spark module continuous voltage so the whole cooktop ticks regardless of dial position. Samsung's own support article (TSG10007324, 'common sounds and operational noises') and RepairClinic both say to pull the burner caps, unplug the range and dry the switches a couple hours to overnight (or warm air from a hair dryer / a low oven run) before condemning anything. If the clicking stops once dry, no part is needed - this is the first thing we test, not the last.
• A switch that still reads closed at OFF after a full dry-out is the igniter spark switch failed closed - the part, not moisture. On Samsung the surface switches live on a harness assembly behind the knobs; a pitted or carbon-tracked contact stays closed and keeps voltage on the DG96-00297A module, so the cooktop sparks non-stop. Samsung supplies it as the DG96-00298D igniter switch + harness assembly (genuine OEM, PS9606643 / AP5917474, fits the NX58 family) or the single-position switch DG96-00298E. We meter each switch for continuity at every knob position - the one that reads closed at OFF is the failed switch - rather than guessing, and we price the switch/harness honestly up front.
• All positions sparking together that survives drying AND switch-isolation is the shared 5-point spark module itself, Samsung DG96-00297A (genuine OEM; replaces DG96-00221A; AP5653580 / 4011639 / PS5577086; fits NX58/NX60). One module pulses every surface electrode, so a stuck internal relay or a shorted module sparks all positions continuously. Because a single module feeds the whole top, a true module fault is all-or-nothing across the cooktop - but we condemn the DG96-00297A LAST, only after the switches and electrodes check out, since on this platform a constant-click is far more often a wet/failed switch than a dead module.
• One burner that clicks constantly while the others behave usually isolates to that position's spark electrode, not the whole-cooktop module. Samsung surface-burner spark electrodes (DG94-00539A small / DG94-00540A medium on the NX58F/NX58H/NX58J/NX58K/NX58M families; the 00540A genuinely interchanges with the position-specific variants DG94-00541A/00602A/00633A, AP5577563 / 4011374 / PS4241442 per RepairClinic) crack at the ceramic insulator or carbon-track at the tip, so they arc continuously or leak spark to the grate even after the knob is released. We compare against the neighbouring burners: if only one position clicks and its switch tests good, the electrode at that spot is the failed part, not the DG96-00297A module.
• A burner that clicks and clicks but never catches a flame - which customers report as 'clicks constantly' - is frequently a misseated or clogged burner cap, not an electrical fault. Spillover carbonizes the ports under a Samsung DG62-00070A (medium, 2-11/16") or DG62-00067A (large, 3-3/4") cap, or the cap is rotated off its locating notch after cleaning, so gas can't reach the electrode gap and the module keeps firing trying to light it. We lift the cap, clear the ports with a fine pin (without enlarging them), reseat it level on the burner head, and only replace the cap/burner head if the ports are eroded - a $0 clean resolves a large share of single-burner constant-click calls.
• A module we replace that clicks non-stop the day it goes in - or burns out a second time - points at the receptacle, not the part. Samsung's spark module needs correct polarity (hot on L, neutral on N) and a true ground; a reversed-polarity or ungrounded outlet makes the DG96-00297A fire erratically. On any repeat-module or fresh-install constant-click we meter the receptacle for polarity and ground, and the range must be on a properly grounded outlet - never a 2-prong adapter or extension cord - so the new module doesn't fail the same way.
• Distinguishing a true constant-click from a normal re-ignition burst keeps the quote honest. Samsung sealed burners re-spark briefly if a flame is blown out, so a quick burst after a draft is by design; persistent clicking with knobs OFF, or clicking that never stops once lit, is the fault. We also confirm a weak-flame-with-hard-ignition case isn't a gas-type/orifice mismatch - a range left on natural-gas orifices after an LP install ticks and struggles to catch, and Samsung ships the LP conversion kit DG94-00635A (orifices + regulator + guide) for exactly that. We pin down the pattern (which burners, knob position, wet vs dry, NG vs LP) before ordering, so a DG96-00298D switch job isn't mis-sold as a DG96-00297A module, or vice versa. Gas/orifice correction is TSSA-certified work, not a parts-swap.

Samsung gas burner clicks constantly in Toronto — the local specifics

• The recurring Samsung-in-Toronto pattern on constant-clicking is moisture in the spark switches - boil-overs and wet cleaning bridge the contacts behind the knobs and keep the DG96-00297A module energized, so the whole NX58/NX60 cooktop ticks with every knob OFF. Most of these clear with a dry-out and a cap/port clean before any part comes out; the genuine part failures we see next are a switch stuck closed (DG96-00298D harness) and, less often, a single cracked electrode (DG94-00540A) on one position. A truly dead shared module is the least common of the three despite being what customers assume.
• We bring the DG96-00297A spark module, a DG96-00298D igniter switch + harness (and the single DG96-00298E switch), a DG94-00539A/00540A electrode set, and DG62-00070A/00067A burner caps so a clicking call is usually a one-visit fix once we've isolated wet-switch vs failed-switch vs electrode vs module. We dry and re-test the switches first - the most common outcome is no part needed at all.

For the full Samsung stove module — every fault, part number and code — see Samsung stove repair in Toronto, and for the same fault across all brands the stove gas burner clicks constantly guide.