How much does washing machine repair cost in Milliken?
Washing machine repair in Milliken typically runs $190–$560 all-in, depending on the fault. The most common call-out is not draining ($190–$360). Every visit starts with a flat $149.95 diagnostic, credited 100% toward your repair, and repairs are backed by a warranty.
- Diagnostic
- $149.95, credited 100% toward your repair
- Warranty
- on parts & workmanship
- Availability
- Same-day & next-day appointments available
Prices in CAD for Milliken; typical ranges — your exact quote is confirmed on-site before any work. Updated .
Most washing machine faults in Milliken come down to a handful of parts — and the majority are worth repairing rather than replacing a 10–13 years appliance. Our certified technicians carry the common washing machine parts on the van, so most Milliken jobs are diagnosed and fixed in a single visit.
Washing Machine repair costs in Milliken
Honest, all-in ranges for common jobs. Every visit starts with a flat $149.95 diagnostic that is credited 100% toward your repair — so you never pay it twice.
| Problem | Parts | Labour | All-in |
|---|---|---|---|
| Not draining | $0–$160 | $140–$220 | $190–$360 |
| Won't spin | $15–$160 | $150–$240 | $230–$420 |
| Leaking water | $15–$200 | $140–$260 | $200–$460 |
| Won't start or won't fill | $20–$260 | $140–$230 | $200–$480 |
| Loud or banging on spin | $30–$220 | $160–$340 | $240–$560 |
| Not agitating (top-load) | $15–$200 | $150–$260 | $220–$460 |
| Door or lid won't lock or open | $30–$170 | $130–$210 | $190–$380 |
| Bad odour or mould (front-load) | $0–$140 | $120–$200 | $190–$340 |
| Diagnostic (credited to the repair) | $149.95 |
Ranges are estimates for common Milliken jobs; your exact quote is confirmed on-site before any work begins. Prices in CAD, updated .
How your repair works
Four simple steps, no surprises.
Book
Call or request a callback. Same-day & next-day appointments available.
Diagnose
A flat $149.95 diagnostic pinpoints the real fault.
Approve
You get an upfront all-in quote first — diagnostic credited 100% toward your repair.
Repaired
Fixed with OEM parts, backed by a 90-day warranty.
Common Washing Machine problems & what we check
Tap any problem for the likely causes, what is safe to check yourself, and what it costs.
Not draining Same-day
Not draining: The cycle finishes (or stalls) with the drum full of water; clothes sit soaking, and the spin won't start because the machine can't pump out.
Also described as: water left in drum, won't drain, standing water, won't pump out
Likely causes
- Clogged drain pump filter or pump impeller jammed by a coin, sock, or lint (Most common)
- Kinked, clogged, or improperly installed drain hose / blocked house standpipe (Common)
- Failed drain pump motor (Common)
- Failed door lock keeping the cycle from advancing, or a control-board fault (Occasional)
✔ Safe to check yourself
- On a front-loader, open the small access panel at the bottom front, place a shallow tray and towels, and slowly drain via the filter cap — then clean the debris filter (the single most common owner fix).
- Check the drain hose behind the machine isn't kinked and isn't pushed too far down the standpipe.
- Run a spin/drain-only cycle to confirm whether the pump tries to run at all.
✖ Leave to a technician
- Don't open the filter cap fast on a full drum — it floods the floor; drain it in stages.
- Pump motor replacement and door-lock/control diagnosis are technician jobs (water + electrical).
Related: Won't spin · Leaking water
Won't spin
Won't spin: The wash runs but clothes come out sopping wet because the machine never reaches full spin (or won't spin at all).
Also described as: no spin, clothes soaking wet, drum won't spin, won't spin out
Likely causes
- Water not draining first, so the machine refuses to spin (see "not draining") (Most common)
- Failed door lock / lid lock — the machine won't spin until it confirms the door is locked (Common)
- Worn drive belt (belt-driven models) slipping or broken (Common)
- Worn motor coupler (direct-drive top-loaders) or a motor/control fault (Occasional)
✔ Safe to check yourself
- First confirm it's draining — a "won't spin" is very often really a drain problem (check the pump filter).
- Make sure the door/lid is fully closed and latching; listen for the lock click at cycle start.
- Confirm the load isn't jammed to one side — redistribute and retry.
✖ Leave to a technician
- Belt, motor coupler, door-lock and motor work require opening the cabinet — technician jobs.
- Don't defeat or tape the door/lid switch — it's a safety interlock.
Related: Not draining · Door or lid won't lock or open · Loud or banging on spin
Leaking water Same-day
Leaking water: Water appears on the floor under or in front of the machine during fill, wash, or spin.
Also described as: water on floor, washer leaking, puddle under washer, leaks during fill
Likely causes
- Loose, cracked, or worn hose — fill hoses, internal hoses, or the drain hose connection (Most common)
- Torn front-load door boot/gasket, or a leaking door seal (Common)
- Failed water-inlet valve or a leaking detergent dispenser/tub seal (Occasional)
- Cracked outer tub or a failed tub seal/bearing assembly (older machines) (Occasional)
✔ Safe to check yourself
- Trace the source: pull the machine out and check the fill and drain hose connections at the back for drips and corrosion.
- Inspect the front-load door gasket folds for trapped debris, tears, or a coin holding the seal open.
- Confirm you're not over-dosing detergent — excess suds can push water past seals.
✖ Leave to a technician
- Shut the water taps off if it's leaking at the inlet; don't run it again until found.
- Inlet-valve, tub-seal and bearing work are technician jobs (water + electrical + dismantling the tub).
Related: Not draining · Bad odour or mould (front-load)
Won't start or won't fill
Won't start or won't fill: The machine is unresponsive, or it powers on and the cycle starts but no water enters the drum.
Also described as: dead, no power, won't turn on, won't fill, no water coming in
Likely causes
- No-fill: water taps off, kinked fill hose, or clogged inlet-valve screens (Most common)
- Failed door lock / lid lock — the cycle won't begin until the door confirms locked (Common)
- Failed water-inlet valve (won't open to admit water) (Common)
- No power: tripped breaker, dead outlet, or a failed control board / user-interface board (Occasional)
✔ Safe to check yourself
- Confirm both hot and cold supply taps are fully open and the fill hoses aren't kinked.
- Check the outlet has power and reset the breaker; confirm the door/lid is closing and latching.
- Clean the inlet-valve mesh screens where the fill hoses connect — mineral/debris clogs are common in hard-water areas.
✖ Leave to a technician
- Inlet-valve, door-lock, and control-board replacement are technician jobs (water + electrical).
- Don't bypass the door interlock to force a start.
Related: Door or lid won't lock or open · Not draining
Loud or banging on spin
Loud or banging on spin: A loud rumble, grind, or banging that builds during high-speed spin; the machine may shake hard or "walk" across the floor.
Also described as: loud spin, banging, rumbling, walking across floor, grinding noise
Likely causes
- Unbalanced load or the machine not level (shipping bolts left in on a new front-loader) (Most common)
- Worn shock absorbers (front-load) or worn suspension rods/springs (top-load) letting the tub bang (Common)
- Worn tub bearing — a rising rumble/grind that gets louder over months (Common)
- A coin or wire caught between the drum and tub (Occasional)
✔ Safe to check yourself
- Confirm the machine is level on all four feet and the load isn't bunched to one side.
- On a newer front-loader, confirm the transit/shipping bolts were removed from the back.
- Check the drum for trapped coins or hardware before they score the tub.
✖ Leave to a technician
- Shock absorbers, suspension rods, and especially tub-bearing replacement require major dismantling — technician jobs.
- Don't keep running it with a roaring bearing; it can wreck the tub and seal.
Related: Won't spin · Not agitating (top-load)
Not agitating (top-load)
Not agitating (top-load): A top-loader fills with water but the agitator (or wash plate) doesn't move clothes through the cycle.
Also described as: agitator not moving, drum fills but doesn't wash, no agitation, clothes not cleaning
Likely causes
- Worn motor coupler (direct-drive Whirlpool/Maytag/Kenmore) — the classic top-load agitation failure (Most common)
- Stripped agitator dogs/cogs (agitator spins on top but doesn't drive the load) (Common)
- Worn or broken drive belt on belt-driven models (Common)
- Failed transmission, lid lock, or motor/control fault (Occasional)
✔ Safe to check yourself
- Confirm the lid is closing and the lid-lock engages — many top-loaders won't agitate with the lid up.
- Listen: a motor that hums or runs but no agitation usually points to the coupler or stripped dogs.
- Don't overload — a packed drum can stall agitation and stress the coupler.
✖ Leave to a technician
- Motor coupler, agitator dogs, belt, and transmission work require opening the cabinet or pulling the agitator — technician jobs.
- Don't keep starting it against a stalled load; that's exactly what wears the coupler.
Related: Won't spin · Loud or banging on spin
Door or lid won't lock or open Same-day
Door or lid won't lock or open: The cycle won't start because the door/lid won't lock, or the machine finished but the door stays locked and won't release.
Also described as: door stuck, door won't open, lid won't lock, can't open after cycle, door locked shut
Likely causes
- Failed door lock / lid lock assembly (the interlock won't confirm "locked") (Most common)
- Worn or misaligned door latch/strike, or a sagging front-load door hinge (Common)
- Stuck-locked after cycle: water still in the drum, so the lock won't release (a drain fault) (Common)
- Control-board fault not sending the lock/unlock signal (Occasional)
✔ Safe to check yourself
- If it's stuck locked after a cycle, check for standing water — a drain blockage keeps the lock engaged; clear the pump filter and the lock usually releases.
- Let the machine sit a few minutes after power-off; many locks release on a timer.
- Locate the manual-release tab (front-loaders usually have one behind the bottom filter panel) and use it gently to free a trapped door.
✖ Leave to a technician
- Don't force or pry the door — you'll break the latch and possibly the hinge.
- Lock-assembly and control-board replacement are technician jobs.
Related: Won't start or won't fill · Not draining
Bad odour or mould (front-load)
Bad odour or mould (front-load): A musty/mildew smell from the drum, with black or grey gunk in the folds of the rubber door gasket and around the detergent drawer.
Also described as: musty smell, mildew odour, mouldy washer, stinky washer, smells bad
Likely causes
- Mould/biofilm growing in the door-gasket folds and dispenser from a door kept shut after washing (Most common)
- Detergent and fabric-softener residue build-up feeding the biofilm (Common)
- Standing water in the gasket or a slow/partial drain leaving moisture behind (Common)
- Cold-water-only, high-efficiency, low-water washing that never gets hot enough to clear residue (Occasional)
✔ Safe to check yourself
- Wipe the door-gasket folds dry after each wash and leave the door (and detergent drawer) ajar between loads — the single best fix and prevention.
- Run a hot tub-clean / "Self Clean" cycle with a washer cleaner or plain bleach on an empty drum.
- Pull out and wash the detergent drawer; reduce detergent and softener dosing.
✖ Leave to a technician
- If the smell persists after cleaning, a torn gasket harbouring mould or a partial drain blockage needs a technician.
- Don't bleach a torn gasket and call it done — a torn boot also leaks and must be replaced.
Related: Leaking water · Not draining
Why homeowners across Milliken call us
Repairs are carried out by our certified technicians — Appliance Repair Near is a Red Seal certified, 313A Licensed, TSSA Certified, ODP Certified company — backed by $2,000,000+ general liability insurance and a 90-day workmanship warranty on every job.
Red Seal technician
Work done by a vetted, certified technician — not a rotating subcontractor.
Licensed & gas-certified
313A refrigeration licence and TSSA gas certification for safe, code-correct repairs.
$2,000,000+ insured
Fully insured for general liability, so your home is protected during the repair.
90-day warranty
Parts and workmanship are warrantied — if it's not right, we come back.
OEM parts on the van
Common parts are stocked, so most jobs are completed on the first visit.
Upfront pricing
A flat $149.95 diagnostic, credited 100% toward your repair, and a quote before any work.
What our credentials mean for you
- Red Seal Certified
- The interprovincial standard for skilled trades — a journeyman who passed the national appliance-service exam.
- 313A Licensed
- Ontario's refrigeration & air-conditioning systems mechanic licence — legally required to work on sealed cooling systems.
- TSSA Certified
- Technical Standards & Safety Authority gas certification — qualified to work safely on gas appliances.
- ODP Certified
- Ozone Depletion Prevention certification — licensed to handle refrigerants responsibly and to code.
Repair or replace your washing machine?
A simple rule of thumb: if the repair costs more than half the price of a comparable new unit and the appliance is near the end of its life, replacement may make more sense.
A washing machine typically lasts – and costs $1,100–$1,900 to replace — so most faults under about $450 are worth fixing. We'll always tell you honestly when a repair isn't worth your money.
Keep your washing machine running
Simple habits that prevent the most common Milliken repairs.
- Leave the door and detergent drawer open between washes and wipe the door gasket dry — the top prevention for front-load odour and mould.
- Clean the drain pump filter (front-loaders, behind the small bottom-front panel) every few months to prevent drain and spin faults.
- Use the correct amount of HE detergent — over-dosing causes excess suds that clog the pump and leave residue.
- Keep the machine level on all four feet and balance loads so the tub doesn't bang and wear the shocks/suspension on spin.
- Inspect the fill hoses for bulges or cracks and replace rubber hoses about every 5 years (braided-steel hoses last longer).
- Run a hot tub-clean cycle monthly to clear detergent residue and biofilm before it smells.
Servicing Washing Machines across Milliken
Homes here: Milliken is the Markham-side community of Milliken Mills, in south-central Markham south of Highway 407 and right up against Steeles Avenue, the municipal line that splits it from Scarborough. It divides into Milliken Mills East (Kennedy Road over to McCowan Road) and Milliken Mills West (around Warden and Kennedy), with 14th Avenue, Highglen Avenue and Denison Street running east-west through it and Brimley Road north-south. Old Milliken's Corners farmland was subdivided as the farms gave way through the 1970s, 80s and 90s. Milliken Mills West developed the earlier, roughly 1970s through the 1980s, and carries detached, link and semi-detached homes; Milliken Mills East filled in later, roughly 1980 to 2000, and runs heavily to detached and link houses. The stock overall is two-storey three- and four-bedroom red and brown brick on narrow 25-to-35-foot lots with single or double attached garages fronting the house and a private drive. The exception is the multi-residential stock on the Markham side along the Kennedy Road corridor — the mid-rise Casa Del Sol condos at 7363 and 7373 Kennedy near Denison (an eight-storey building from 2008), plus the condo and townhome pockets at Kennedy and 14th Avenue near the Milliken Mills Community Centre. It is one of the GTA's most heavily Chinese and East Asian communities — Pacific Mall and the Steeles/Kennedy Asian retail strip anchor the corridor at Kennedy and Steeles, just across the Toronto line — so kitchens here lean to heavy daily cooking and big-family use.
Parts & timing: Common parts are typically same-day from our Markham and Scarborough channels; Milliken sits in Markham's south end against Steeles, so the Milliken Mills East and West streets, the Kennedy Road condo corridor and the McCowan corridor are all a short parts run.
Water & disposal: Milliken is part of the City of Markham, so the same municipal water supply and appliance disposal rules apply — see appliance repair in Markham for the full water profile and disposal details.
Coverage: We cover Milliken end to end — Milliken Mills East and West, the streets off Kennedy, Warden, McCowan, Brimley, 14th Avenue, Highglen and Denison, the Kennedy Road condo corridor including the Casa Del Sol mid-rise near Denison and the Kennedy and 14th Avenue pockets, and the blocks near the Milliken Mills Community Centre.
Towers & condos: N/A
More appliance repair in Milliken
Other appliances
Nearby cities
Frequently asked questions
Why is my washer not draining?
Why won't my washer spin?
Why is my washer leaking water?
Why won't my washer start or fill with water?
Why is my washer loud or banging during the spin cycle?
Why won't my top-load washer agitate?
Why won't my washer door lock or open?
Why does my front-load washer smell musty or mouldy?
Do you charge for the diagnostic?
How soon can you come out?
Are you licensed and insured?
Do you use genuine parts?
Need your washing machine fixed in Milliken?
Same-day & next-day appointments available. Flat $149.95 diagnostic, credited 100% toward your repair, and a 90-day warranty on every repair.
Call (647) 490-7878