(647) 490-7878
Washing Machine repair in the GTA — Appliance Repair Near

Washing Machine Leaking water — Causes, Fixes & Repair Costs

Fast, honest washing machine repair by Anthony, a Red Seal & 313A licensed technician. Flat $149.95 diagnostic, credited 100% toward your repair.

  • Red Seal Certified
  • $2,000,000+ Insured
  • Warranty
Red Seal Certified
313A & TSSA Licensed
$2,000,000+ Insured
90-Day Warranty

Why is my washer leaking water?

Most common cause on a washing machine in the GTA: loose, cracked, or worn hose — fill hoses, internal hoses, or the drain hose connection. A typical repair runs $200$460 all-in, including the $149.95 diagnostic, credited 100% toward your repair. Active leaks risk flooring and, in condos/upper floors, a downstairs water-damage claim. Same-day

Prices in CAD for the GTA; typical ranges — your exact quote is confirmed on-site before any work. Updated .

Most washing machine faults in the GTA come down to a handful of parts — and the majority are worth repairing rather than replacing an appliance that typically lasts 10–13 years. Anthony is a Red Seal certified technician who carries the common washing machine parts on the van, so most jobs in the GTA are diagnosed and fixed in a single visit.

Washing Machine repair costs in the GTA

Honest, all-in ranges for common jobs. Every visit starts with a flat $149.95 diagnostic that is credited 100% toward your repair — so you never pay it twice.

Washing Machine repair costs in the GTA (CAD) — typical all-in ranges, June 2026
ProblemPartsLabourAll-in
Leaking water$15$200$140$260$200$460
Diagnostic (credited to the repair)$149.95

Ranges are estimates for common jobs in the GTA; your exact quote is confirmed on-site before any work begins. Prices in CAD, updated .

How your repair works

Four simple steps, no surprises.

1

Book

Call or request a callback. Same-day & next-day appointments available.

2

Diagnose

A flat $149.95 diagnostic pinpoints the real fault.

3

Approve

You get an upfront all-in quote first — diagnostic credited 100% toward your repair.

4

Repaired

Fixed with OEM parts, backed by a 90-day warranty.

Common Washing Machine problems & what we check

Tap any problem for the likely causes, what is safe to check yourself, and what it costs.

Leaking water Same-day$200$460

Leaking water: Water appears on the floor under or in front of the machine during fill, wash, or spin.

Also described as: water on floor, washer leaking, puddle under washer, leaks during fill

Likely causes

  1. Loose, cracked, or worn hose — fill hoses, internal hoses, or the drain hose connection (Most common)
  2. Torn front-load door boot/gasket, or a leaking door seal (Common)
  3. Failed water-inlet valve or a leaking detergent dispenser/tub seal (Occasional)
  4. Cracked outer tub or a failed tub seal/bearing assembly (older machines) (Occasional)

How we diagnose it — in order

  1. Pin down WHEN the water appears, since cycle timing localizes the source: leaking during fill points to the supply side, leaking during wash/agitation points to the door boot or excess suds, and leaking during drain/spin points to the pump or its hoses. Run a cycle and watch which phase produces the puddle before opening anything.
  2. Rule out the no-tools/no-cost cause first: confirm the customer is using only HE detergent and a small dose. Over-sudsing pushes foam and water past the door seal, dispenser, and vents during the first agitation. Run a clear-water rinse cycle and confirm the leak stops before condemning any part.
  3. Check the back of the machine: inspect the hot/cold fill hoses and the water-inlet valve connections for weeping, and confirm the rubber washers are seated and the couplings are snug. A slow puddle that appears while the machine sits idle usually traces to the inlet valve or a fill-hose connection rather than an internal part.
  4. On a front-loader, peel back and inspect the full door boot gasket, especially the lower fold, for tears, trapped debris, or clogged drain weep holes. On a top-loader, this is where you check the tub-to-pump hose and clamps. A boot that leaks only under a full load or during agitation hides damage in the bottom that is easy to miss.
  5. Pull and clean the pump filter/coin trap, then inspect the drain pump housing and the pump-to-tub hose with the machine running on drain/spin. Look for cracks in the pump volute, a weeping pump shaft seal, or a loose hose clamp. Confirm whether water exits here specifically during drain and spin before ordering a pump.
  6. If supply, suds, boot, hoses, and pump are all confirmed dry, the definitive cause is the tub/bearing seal behind the drum (often signalled by rusty grease tracks, drum roughness, or play at the shaft). This requires major disassembly and a seal/bearing kit, so condemn it last only after the cheaper sources above are ruled out.

✔ Safe to check yourself

  • Trace the source: pull the machine out and check the fill and drain hose connections at the back for drips and corrosion.
  • Inspect the front-load door gasket folds for trapped debris, tears, or a coin holding the seal open.
  • Confirm you're not over-dosing detergent — excess suds can push water past seals.

✖ Leave to a technician

  • Shut the water taps off if it's leaking at the inlet; don't run it again until found.
  • Inlet-valve, tub-seal and bearing work are technician jobs (water + electrical + dismantling the tub).
If you wait: A small seal or hose leak left alone can warp flooring, grow mould behind the machine, and a weeping tub seal eventually destroys the bearing — a major repair.
Time on site
45 min–2 hours (more if tub seal)
Visits
Usually 1; tub-seal/bearing jobs may be 2
Typical all-in
$200$460
Repair vs. replace
Hose/gasket/valve leaks are well worth repairing. A cracked tub or seal+bearing on a 10+ yr machine often tips toward replacement — get the quote first.
Error codes
Samsung LC/LC1 (leak sensor), LG LE1 (leak)

Related: Not draining · Smells musty or mouldy (front-load)

Ready to get it fixed?

Call now — (647) 490-7878 90-day warranty · flat $149.95 diagnostic credited 100% toward your repair

Why homeowners across the GTA call us

Every repair is led by Anthony, a Red Seal interprovincial journeyman who is 313A Licensed, TSSA Certified, ODP Certified, with his team working under his direct leadership — backed by $2,000,000+ general liability insurance and a 90-day workmanship warranty on every job.

Red Seal-led team

Every job is overseen by Anthony, a certified journeyman, and handled by his own trusted team.

Licensed & gas-certified

313A refrigeration licence and TSSA gas certification for safe, code-correct repairs.

$2,000,000+ insured

Fully insured for general liability, so your home is protected during the repair.

90-day warranty

Parts and workmanship are warrantied — if it's not right, we come back.

OEM parts on the van

Common parts are stocked, so most jobs are completed on the first visit.

Upfront pricing

A flat $149.95 diagnostic, credited 100% toward your repair, and a quote before any work.

What our credentials mean for you

Red Seal Certified
The interprovincial standard for skilled trades — a journeyman who passed the national appliance-service exam.
313A Licensed
Ontario's refrigeration & air-conditioning systems mechanic licence — legally required to work on sealed cooling systems.
TSSA Certified
Technical Standards & Safety Authority gas certification — qualified to work safely on gas appliances.
ODP Certified
Ozone Depletion Prevention certification — licensed to handle refrigerants responsibly and to code.

Repair or replace your washing machine?

A simple rule of thumb: if the repair costs more than half the price of a comparable new unit and the appliance is near the end of its life, replacement may make more sense.

A washing machine typically lasts and costs $1,100$1,900 to replace — so most faults under about $450 are worth fixing. We'll always tell you honestly when a repair isn't worth your money.

Keep your washing machine running

Simple habits that prevent the most common the GTA repairs.

  • Leave the door and detergent drawer open between washes and wipe the door gasket dry — the top prevention for front-load odour and mould.
  • Clean the drain pump filter (front-loaders, behind the small bottom-front panel) every few months to prevent drain and spin faults.
  • Use the correct amount of HE detergent — over-dosing causes excess suds that clog the pump and leave residue.
  • Keep the machine level on all four feet and balance loads so the tub doesn't bang and wear the shocks/suspension on spin.
  • Inspect the fill hoses for bulges or cracks and replace rubber hoses about every 5 years (braided-steel hoses last longer).
  • Run a hot tub-clean cycle monthly to clear detergent residue and biofilm before it smells.

Frequently asked questions

Why is my washer leaking water?
Water appears on the floor under or in front of the machine during fill, wash, or spin. Most common cause: Loose, cracked, or worn hose — fill hoses, internal hoses, or the drain hose connection. A typical repair is $200$460, including the $149.95 diagnostic credited 100% toward your repair.
Do you charge for the diagnostic?
The diagnostic is a flat $149.95, and it is credited 100% toward your repair — so if you go ahead with the fix, it isn't an extra charge.
How soon can you come out?
Same-day & next-day appointments available across the GTA. Call (647) 490-7878 and we'll give you the next available slot.
Are you licensed and insured?
Yes. Repairs are performed by Anthony, who is Red Seal Certified, 313A Licensed, TSSA Certified, ODP Certified, and the work is backed by $2,000,000+ general liability insurance and a 90-day warranty.
Do you use genuine parts?
Yes — we fit OEM parts and stock the common ones on the van, so most repairs are completed in a single visit.

Need your washing machine fixed in the GTA?

Same-day & next-day appointments available. Flat $149.95 diagnostic, credited 100% toward your repair, and a 90-day warranty on every repair.

Call (647) 490-7878
Call now Callback