Frigidaire Washing Machine Repair in Toronto — Won't start or won't fill

• E41 is the won't-start signature on the Frigidaire Affinity/FFFW front-loads: the control reads the door switch as open, so it never locks the door and the cycle never advances past the lock step. The part is the door lock & switch assembly 131763202 (also sold as 131763256 / 1317632, paired with strikers 131763310 / 131763302) -- when its solenoid or its switch contacts fail, the board reads 'door open' even with the door shut. We continuity-test the lock micro-switches before condemning anything; on this platform a clicking-but-not-locking door is almost always the latch, not the board.
• E42 is the related lock fault -- the door stays locked (or the control can't read it as unlocked) after a cycle, which then blocks the next start. Sometimes it is genuine (water still in the tub holds the lock for safety), sometimes the latch solenoid is stuck or the control isn't sensing the unlock position. We power-cycle at the breaker for two minutes first (a one-time electronic hiccup often clears), then test the same 131763202 lock assembly and its harness before quoting a board -- the cure overlaps with E41 because it is the same latch hardware.
• E68 is the won't-start that is a stuck console button, not a mechanical fault: the control detects a key held active on the touchpad/membrane and refuses to start. The diagnosis is in the service routine -- hold START and CANCEL together for ~10 seconds to enter the key test and find the stuck pad; cleaning the membrane with isopropyl frees a debris-stuck key. If the key tests free but E68 persists, the cure is the user-interface/control board 134556600 (supersedes to 137007000, AP4362398). We always run the key test before ordering -- this is the cheapest won't-start fix and the one most often misdiagnosed as a dead machine.
• E5E is the won't-start that is a board-to-board communication failure: the main control board can't talk to the motor/speed control board, so the cycle aborts before it can run. The honest first move is to reseat every connector at both boards and inspect the harness for chafe or moisture -- a loose plug throws E5E far more often than a dead board. When the wiring checks out, the fault is split between the two boards: in the field the motor/speed control board 134743500 (AP3891780) is the more common hardware failure, so we lead our suspicion there, while a confirmed E5E that survives reseating and a good motor board points back at the main control board 137006000 (AP4358809). The exact board is drawn by model/serial.
• E43 and E45 are the won't-start codes that genuinely point at the main control board: E43 is a control-board / door-lock-circuit fault and E45 is an internal control-board fault, and both can leave the machine lit but unable to start a cycle. The standard order of elimination is door lock and its wiring first (because E43 can be triggered by the latch circuit, not the board), and only then the main control board 137006000 (AP4358809, which supersedes 134523103 / 134732003 / 134855503). We don't lead with the most expensive part -- the board is the last suspect after the latch and harness clear.
• A completely dead panel -- no lights, no beep -- is the won't-start that is line-side, not the wash electronics. The no-start checklist starts at the wall: a tripped breaker, a tripped or non-resetting GFCI, or a loose plug. Frigidaire's install specs call for a dedicated non-GFCI circuit, and a nuisance-tripping GFCI is a frequent false 'dead washer.' Inside the cabinet the next checks are the line filter / thermal line fuse for continuity before any board is condemned -- a no-power machine is a voltage problem until proven a board problem.
• A power-surge-killed board is its own won't-start case on this platform: after a hit, the panel goes fully dark and no diagnostic code can even be read. The main control board is the usual casualty -- depending on the Affinity model that is either the 137006000 (AP4358809) or the model-specific 137006005 (AP4982230), which is a separate board for certain FAFW3001/FAFW3801 models rather than a surge-hardened variant of the same part, so we draw the exact board by model/serial. We confirm the unit is getting 120 VAC at the board input and the line fuse has continuity before condemning it -- but a dark, codeless Affinity that passes its voltage and fuse checks after a storm is the textbook control-board replacement, and it is the one no-start cause where chasing the door latch accomplishes nothing.

Frigidaire won't start or won't fill in Toronto — the local specifics

• The recurring Toronto pattern on a Frigidaire won't-start is that it is a door-latch or a line-side fault far more often than a control board: E41/E42 calls are overwhelmingly the 131763202 lock assembly, and a meaningful share of 'totally dead' calls are a tripped GFCI/breaker on the condo or basement circuit rather than anything inside the machine. E68 stuck-key calls clear at the key test surprisingly often. When it is a board, E5E points at the motor/speed control board more often than the main board. We confirm the door latch, the outlet and the keypad before we ever quote a board.
• We roll to these calls with the 131763202 door lock/latch assembly (plus strikers 131763310/131763302) on the van, a multimeter for the outlet/GFCI, breaker and line-fuse continuity checks, and the model-matched main control board 137006000 / motor-speed control board 134743500 / UI board 134556600 (137007000) drawn from local distributor stock once the model and serial confirm the exact board for that Affinity series.

For the full Frigidaire washing machine module — every fault, part number and code — see Frigidaire washing machine repair in Toronto, and for the same fault across all brands the washing machine won't start or won't fill guide.