Frigidaire Dishwasher Repair in Toronto — Not filling with water

• i10 is the signature Frigidaire not-filling code on this i-code platform: third-party Electrolux/Frigidaire service literature defines i10 as a low-fill / water-inlet time-out — the control did not sense the expected water level inside the time window and aborts. The diagnostic walk is supply-first, not part-first: confirm the under-sink shut-off is open, the fill/supply hose is not kinked, and the inlet screen is clear before condemning hardware. On FFCD/FGID Gallery tubs we always rule out a starved supply on an i10, because a closed tap or a pinched hose throws the exact same code as a dead valve.
• The water inlet valve 154637401 (AP4321824 / PS1990907) is the number-one orderable not-filling part: it is a single 120V solenoid valve that meters fill water, and when the solenoid coil opens, sticks, or the inlet screen silts up, voltage is present at fill but little or no water enters — the cycle starts, fails to reach level, and parks on i10. This OEM number supersedes a long Electrolux-lineage list (154219601, 154359801, 154373301, 154445901, 154476101 and others), so we cross the supersession to the data-plate model and test the solenoid for continuity before swapping rather than guess from the badge.
• A stuck or scaled overfill float is a distinct Frigidaire not-filling fault from the valve: the water-level float switch assembly 154773201 (AP4982393 / PS3492842) is the safety that signals the inlet valve to shut OFF once the tub reaches level, and when the float binds high (mineral scale on the float guide, or debris under it) the control reads 'already full' and never opens the valve — a no-fill with a perfectly good 154637401. We check the float moves freely by hand and clean its guide before ordering, because a new valve behind a stuck float still won't fill.
• A clogged inlet screen / strainer from Toronto's hard water is a no-part (or near-no-part) Frigidaire not-filling fix: the small screen inside the inlet port of the 154637401 valve silts with mineral and pipe debris, so the valve opens electrically but flow drops below the i10 fill window. We shut the supply, disconnect the fill hose at the valve, and clean the screen with a soft brush — a partial fill that times out as i10 with the solenoid testing good is very often this scale-and-debris restriction, not a failed valve.
• A pressure/level-sensing hose fault is a less obvious not-filling cause on these tubs: the small pressure hose that runs from the sump to the level sensor can clog, split, or pop off, so the control mis-reads the water level and either stops fill early or never confirms it — logging i10 with adequate water actually present. We inspect the hose seating and check for splits before ordering any valve or float, because a sensing-path fault won't be fixed by a new fill valve.
• An i30 base-pan flood-protect state can be mistaken for not-filling: Frigidaire defines i30 as water/overflow detected in the base pan, where a styrofoam anti-flood float rises and the control holds the drain pump running to keep the floor dry. In our experience that flood-protect mode also blocks the normal fill, so the owner can report 'it won't fill' when the machine is actually protecting against a leak. We never reset-and-run an i30; we vacuum and fully dry the pan so the float drops, then chase the water path (a tired door-gasket corner or a weeping inlet fitting) before clearing the code, because clearing it without drying just re-triggers the same state.
• Less commonly, a door-latch fault presents as a fill problem rather than the usual won't-start: on this platform the control won't open the fill valve unless it senses the door latched (Frigidaire reports a door-not-latched state as CL/Cd, which fundamentally means 'door open'). Most door-latch failures stop the cycle from starting, but a marginal latch hook or a microswitch that drops out part-way — or a door bumped open mid-cycle — can leave a unit that started but stalls before or at fill. The part is the complete door latch and switch assembly 5304525218 (AP6989890; supersedes 5304516818, 154722401, 154543901, 154758101, 5304527418) — latch and switch are one assembly here. We treat this as the less-likely cause behind the valve, screen, and float, and listen for the switch click on a live close before condemning it.

Frigidaire not filling with water in Toronto — the local specifics

• The recurring Toronto pattern on Frigidaire not-filling is that the i10 is supply-side as often as it is the valve: a barely-open or seized under-sink shut-off, a kinked fill hose tucked behind a tight cabinet, or a scale-silted inlet screen from the hard water — we confirm a live fill and clean the screen before condemning the 154637401. The genuine part failures cluster on the inlet valve solenoid and, less often, a scaled-stuck overfill float reading 'full' so the valve never opens.
• We bring the 154637401 inlet valve and 154773201 float switch to these calls, plus a meter to confirm voltage-at-fill versus flow and a soft brush to clear the scaled inlet screen. We keep the 5304525218 latch assembly on the van as a backup in case the no-fill turns out to be a door-not-latched (CL/Cd) gate rather than a water-path fault, though that is the less-common cause here.

For the full Frigidaire dishwasher module — every fault, part number and code — see Frigidaire dishwasher repair in Toronto, and for the same fault across all brands the dishwasher not filling with water guide.