Kenmore Dryer Repair in Toronto

How much does Kenmore dryer repair cost in Toronto?

Kenmore dryer repair in Toronto typically runs $250–$420 all-in, depending on the fault. The most common Kenmore call-out is not heating ($250–$390). Every visit starts with a flat $149.95 diagnostic, credited 100% toward your repair, and repairs are backed by a 90-day warranty.

Diagnostic: $149.95, credited 100% toward your repair
Warranty: 90-day on parts & workmanship
Availability: Same-day & next-day appointments available

Prices in CAD for Toronto; typical ranges — your exact quote is confirmed on-site before any work. Updated June 2026.

Most Kenmore dryer faults in Toronto come down to a handful of parts — and the majority are worth repairing rather than replacing a 10–13 years appliance. Anthony is a Red Seal certified technician who carries the common dryer parts on the van, so most Toronto jobs are diagnosed and fixed in a single visit.

How your repair works

Four simple steps, no surprises.

1

Book

Call or request a callback. Same-day & next-day appointments available.

2

Diagnose

A flat $149.95 diagnostic pinpoints the real fault.

3

Approve

You get an upfront all-in quote first — diagnostic credited 100% toward your repair.

4

Repaired

Fixed with OEM parts, backed by a 90-day warranty.

Kenmore dryer parts we stock

Kenmore is a Sears RETAIL BADGE, not a manufacturer — the real maker is decoded from the FIRST 3 DIGITS of the model number on the door/cabinet tag. There are no "Kenmore" part numbers: the parts ARE the donor maker's parts. The dominant Kenmore dryer donors are 110.=Whirlpool-built (29" rear-fuse + 27" Duet platforms — blown thermal fuse from a clogged vent is THE no-heat story), 796.=LG-built (Flow Sense d80/d90/d95 vent codes), and 417.=Frigidaire/Electrolux-built (the Kenmore Elite "417 series" — E64 open-heater is the signature). We decode the FULL model and serial before the visit so the right donor van kit is on board, not a second trip.

Signature Kenmore faults

110. Whirlpool-built: thermal fuse blown / element open — tumbles but no heat; root cause is almost always a clogged vent run that cooked the fuse (most common (110. = largest GTA installed base))
796. LG-built: Flow Sense exhaust restriction + thermistor faults — machine derates/extends cycles or won't heat; display shows d80/d90/d95 or tE1 (common (Kenmore Elite 796.))
417. Frigidaire/Electrolux-built: heater open circuit — no heat with E64 stored; element reads open on a meter (common (Kenmore Elite 417. series))
Drum rollers / belt / idler wear (all donors) — thump, squeal, or drum free-wheels while motor runs (common — donor-specific kit numbers)

Kenmore dryer OEM parts — reference numbers & price bands (CAD), June 2026
Part	OEM number	Price band
Whirlpool-built (110.) thermal fuse, 196F/91C	`3392519 (WP3392519 / PS11741460)`	$15–$30
Whirlpool-built (110.) heating element, 240V/5400W	`8544771 (WP8544771 / PS11746337)`	$70–$130
Whirlpool-built (110.) thermal cut-off kit	`279973 (AP3094323)`	$30–$55
LG-built (796.) poly-V drive belt	`4400EL2001A (PS3522928)`	$20–$40
LG-built (796.) exhaust thermistor	`6323EL2001B (PS3529026)`	$20–$40
Frigidaire/Electrolux-built (417.) heating element, 240V/5500W	`134792700 (AP4368653 / PS2349309)`	$70–$130

Error codes we see on Kenmore dryers

110. AF: Whirlpool-built: airflow restriction — clean the FULL vent run, not just the lint screen
110. F01 / L2: Whirlpool-built: F01 main control board internal short; L2 one 240V leg down (breaker/cord check first)
796. d80 / d90 / d95: LG-built Flow Sense: 80/90/95% exhaust blockage — vent service, usually not a parts job
796. tE1: LG-built: thermistor (temperature-sensor) open-circuit fault
417. E64: Frigidaire/Electrolux-built: heater open circuit — test element 134792700 for continuity

Kenmore notes

Text us the FULL model number off the door-jamb or cabinet tag (e.g. 110.xxxxxxxx) — the first 3 digits decode the maker and which van kit we load; it saves a diagnostic surprise and usually a second visit.
110. and 796. share the Kenmore Elite badge but are completely different machines underneath — a 110. is Whirlpool fuse-and-element mechanics, a 796. is LG Flow Sense electronics. Same nameplate, different parts book.
A blown 110. thermal fuse (3392519) never fails on its own — we replace it AND clear the full vent, or it blows again next month.
796. d-codes are a vent-service call, not a parts job — clearing the duct is cheaper than the part owners brace for; CL on an LG-built Kenmore is child-lock, not a fault.
417. Kenmore Elite that names its own fault: E64 = heater open, so diagnosis is fast and the visit is mostly the fix.
Sears warranty is orphaned, but maker-side parts logic is intact — every donor part is current OEM stock.

Model families: 110.xxxxxxx — Whirlpool-built (29" rear-fuse classics + 27" Duet front-loads; enormous GTA installed base) · 796.xxxxxxx — LG-built (Kenmore Elite; Flow Sense vent codes) · 417.xxxxxxx — Frigidaire/Electrolux-built (Kenmore Elite 417 series; E64 heater code)

Warranty check: Sears coverage is effectively orphaned, but maker-side parts logic still applies (e.g., the LG or Whirlpool component terms) — we decode and check.

Safety history: Recall exposure follows the REAL maker — serial-check on the builder's database once the prefix is decoded.

Availability: Decode-then-source: there is no Kenmore parts shelf — once the prefix is read off the model tag we source from the donor's channel. 110. pulls the most-stocked Whirlpool dryer parts in Canada (fuse/kit/element ride on the van); 796. pulls LG laundry parts (same/next-day GTA); 417. pulls 134-prefix Frigidaire/Electrolux parts (cheap and stocked). Confirm by full model/serial before quoting. These are OEM reference numbers — exact fitment is confirmed against your model and serial on-site.

Why homeowners across Toronto call us

Every repair is led by Anthony, a Red Seal interprovincial journeyman who is 313A Licensed, TSSA Certified, ODP Certified, with his team working under his direct leadership — backed by $2,000,000+ general liability insurance and a 90-day workmanship warranty on every job.

Red Seal-led team

Every job is overseen by Anthony, a certified journeyman, and handled by his own trusted team.

Licensed & gas-certified

313A refrigeration licence and TSSA gas certification for safe, code-correct repairs.

$2,000,000+ insured

Fully insured for general liability, so your home is protected during the repair.

90-day warranty

Parts and workmanship are warrantied — if it's not right, we come back.

OEM parts on the van

Common parts are stocked, so most jobs are completed on the first visit.

Upfront pricing

A flat $149.95 diagnostic, credited 100% toward your repair, and a quote before any work.

What our credentials mean for you

Red Seal Certified: The interprovincial standard for skilled trades — a journeyman who passed the national appliance-service exam.
313A Licensed: Ontario's refrigeration & air-conditioning systems mechanic licence — legally required to work on sealed cooling systems.
TSSA Certified: Technical Standards & Safety Authority gas certification — qualified to work safely on gas appliances.
ODP Certified: Ozone Depletion Prevention certification — licensed to handle refrigerants responsibly and to code.

Servicing Dryers across Toronto

Parts & timing: Common parts typically same-day via Scarborough and North York distributor branches.

Costs for every common fault, plus the full coverage map and disposal rules, live on dryer repair in Toronto and the Toronto hub.

Frequently asked questions

How fast can you repair my Dryer in Toronto?

We offer same-day and next-day Dryer repair across Toronto with OEM parts stocked for first-visit fixes.

Do you charge for the diagnostic?

The diagnostic is a flat $149.95, and it is credited 100% toward your repair — so if you go ahead with the fix, it isn't an extra charge.

How soon can you come out?

Same-day & next-day appointments available across Toronto. Call (647) 490-7878 and we'll give you the next available slot.

Are you licensed and insured?

Yes. Repairs are performed by Anthony, who is Red Seal Certified, 313A Licensed, TSSA Certified, ODP Certified, and the work is backed by $2,000,000+ general liability insurance and a 90-day warranty.

Do you use genuine parts?

Yes — we fit OEM parts and stock the common ones on the van, so most repairs are completed in a single visit.

Do you service Kenmore dryers?

Yes — Kenmore dryers are one of the brands we work on across Toronto, with OEM parts stocked for first-visit fixes.

Need your Kenmore dryer fixed in Toronto?

Same-day & next-day appointments available. Flat $149.95 diagnostic, credited 100% toward your repair, and a 90-day warranty on every repair.

Call (647) 490-7878